xerox dc242 error code 042-326

xerox dc242 error code 042-326

xerox dc242 error code 042-326 Fault code Xerox DC 240/242/250/252/260/WC 7655/7665/7675/7755/7765/7775 hata kodu verirse 05322603702 arayın.

xerox dc242 error code 042-326
xerox dc242 error code 042-326

xerox dc242 error code 042-326

Xerox DC 240/242/250/252/260/WC 7655/7665/7675/7755/7765/7775

Fault Code:Description / Notes:
002-770The Hard Drive (HDD) is over capacity
003-xxx codesGenerally: Communication Errors between boards in the machine
005-xxx codesGenerally: Document Feeder problems
005-121 thru 005-158Document Jams
005-194 thru 005-199Document size mismatch problems
005-275/280Document Feeder communication errors
005-281 thru 005-283Document Tray lift problems
005-284Document APS (Automatic Paper Sensors) failure (there are 3 sensors which detect various paper widths on the Document Feeder)
005-285Document Nudger up failure
005-286Document feed-out sensor failure
005-303Document Tray Interlock is open
005-304Document Platen Interlock opened during a job
005-305Document Top Cover Interlock opened during a job
005-306Document Tray Interlock opened during a job
005-308/309Document Left Cover is open or opened during a job
005-906 thru 005-918Document is still detected in feeder after power-on or after closing one of the document door interlocks
010-xxx codesGenerally: Fuser faults
010-311Open Fuser Thermistor was detected (white connector)
010-319 *Fuser Heat Control problem *NOTE: This code must be cleared from Diagnostic Mode… details below.
010-320 **Fuser Overheat problem… (can be reported by any of the 3 thermistors in the fuser) ** NOTE: This code must be cleared from Diagnostic Mode… details below.
010-322 thru 010-323Fuser Thermistor open circuit detected (NCCenter Sensor or Rear Thermistor)
010-324***Fuser NVM (Memory) failure *** NOTE: This code must be cleared from Diagnostic Mode… details below.
010-326 thru 010-327Fuser Heat Control problems
010-330Fuser Motor failure
010-420Fuser Module nearing end of life… NOTE: Read below for fuser count reset info.
010-421Fuser Module “End of Life”… NOTE: If the fuser is still good, you can replace the Fuser Reset Fuse (on top of the fuser) and possibly the Fuser Heat Roll to keep it running.
012-xxx codesGenerally: Finisher problems
013-xxx codesGenerally: Finisher / Booklet Maker problems
016-xxx codesGenerally: Options or Software failures
016-311Scanner not detected
024-340 thru 024-747ESS (Network Controller) problems
024-910 thru 024-917Paper size Sensing problems (in one of the paper drawers)
024-919Face Up Tray interlock open
024-920/922Face Down Tray 1 full / Face Down Tray 2 full
024-923/924/ 925Toner Cartridge Empty – Y / M / C
024-927/930OCT (Offset Catch Tray) full / Stacker Tray full
024-934 thru 024-939Paper type mismatch errors
024-946/947/ 948/949Tray not in position (T1/2/3/4)
024-950/951/ 952/953/954/ 955/956No Paper in tray (T1/2/3/4/5/6/7)
042-313Rear Fuser Cooling Fan failure
042-320/321/ 322/323Drum Motor failures – 320=Y, 321=C, 322=M, 323=K (black)
042-324IBT Belt Drive Motor failure
042-325Main Motor failure
042-326IBT Belt Home position not detected in time
042-327IBT Belt Position failure
042-328IBT Belt Edge Sensor failure
042-330Fuser Exhaust Fan failure
042-331Blower Motor Fan failure
042-600/601/ 602Belt Edge timing failures
042-603Suction Filter end of life
045-xxx codesPrinting communication failures
061-320/321ROS (Laser Unit) polygon motor failures
061-323 thru 061-607ROS (Laser Unit) problems
062-357CCD (Scanner) Fan failure
062-360Exposure Carriage position failure.
062-371Exposure Lamp not lighting (or very dim)
071-101 thru 071-105Paper Jams from Tray 1 at takeaway or registration
071-210Tray 1 Lift failure
072-101 thru 072-105Paper jams from Tray 2 at takeaway or registration
072-210Tray 2 Lift failure
073-101 thru 073-105Paper jam from Tray 3 at takeaway or registration
073-210Tray 3 Lift failure
074-101 thru 074-105Paper jam from Tray 4 at takeaway or registration
074-210Tray 4 Lift failure
075-100 thru 075-135Paper jam from Tray 5 at takeaway or registration
075-210/211Tray 5 Lift failure / Lift down failure
077-103 thru 077-118Fuser Exit Sensor jam or final Exit Sensor jam.
077-120Post 2nd BTR Roll Sensor jam
077-123 thru 077-130Inverter jams
077-300Front Cover interlock open
077-301Left Door interlock open
077-302Right Cover interlock open
077-303Transfer Module 2 interlock open
077-909Paper detected in paper path at power-on
078-100 thru 078-151Paper jam from Tray 6 / High Capacity Feeder (HCF) at takeaway or registration
078-250Tray 6 (HCF) Lift failure
078-300HCF (Hi Capacity Feeder) Top Cover interlock open
078-301HCF Docking Interlock open
089-600 thru 089-617Image Registration Control problems
091-311BCR and Black Charge Corotron Cleaner control problem
091-312Black Charge / Preclean HVPS (Hi Volt Power Supply) failure

091-313Drum Cartridge CRUM (chip) communication failure
091-320Black Charge Corona Wire is broken
091-400Waste Toner Bottle replacement needed soon
091-401Black Drum Cartridge near end of life
091-403Black Charge Corotron Assembly near end of life
091-404Black Charge Corotron Assembly has reached end of life
091-411Yellow Drum Cartridge near end of life
091-421Magenta Drum Cartridge near end of life
091-431Cyan Drum Cartridge near end of life
091-910Waste Toner Bottle not detected
091-911Waste Toner Bottle full
091-913Black Drum Cartridge at end of life
091-914 thru 091-916 or 091-921Black Drum Cartridge CRUM communication problems
091-917/920/924/925/927Yellow Drum Cartridge CRUM communication problems
091-918/922/ 928Magenta Drum Cartridge CRUM communication problems
091-919/923/ 926/929Cyan Drum Cartridge CRUM communication problems
091-932Yellow Drum Cartridge end of life
091-933Magenta Drum Cartridge end of life
091-934Cyan Drum Cartridge end of life
092-649/650ADC Sensor Shutter failures
092-651/652IBT Belt ADC Sensor (MOB ADC) failures
092-653 thru 092-660ATC (from Developer Unit) problems…653/657=yellow, 654/658=magenta, 655/659=cyan, 656/660=black
093-300Marking Drawer Interlock open
093-313 thru 093-317Toner Dispense problems… 314=Y, 315=M, 316=C, 317=K (black)
093-320Developer Motor failure
093-421 thru 093-425Toner Cartridges low 421/422=K(black), 423=Y, 424=M, 425=C
093-600 thru 093-912Toner Dispense problems (600=Y, 601=M, 602=C, 603/912=K(Black),
093-918 thruToner CRUM failures (918/924 /925/926/936/ 940=K(black),927/933/937 =Y, 928/934/938 = M , 929/935/939=C
093-940
094-320/3211st BTR (Transfer Roll) retract or contact problems
094-322/3232nd BTR (Transfer Roll) retract or contact problems
102-xxx codesGenerally: Network Controller (ESS) problems
112-700Finisher Punch Dust Box full (hole punch bin)
116-xxx codesGenerally: Network Controller (ESS) problems
123-xxx codesGenerally: UI (control panel) faults
124-xxx codesGenerally: Configuration errors (e.g., serial number disagreement between various boards or machine speed errors, etc)
127-xxx codesPrinting failures

xerox dc242,
xerox dc242 driver,
xerox dc 242 fuser,
xerox dc 242 calibration,
xerox dc 242 toner,
xerox dc 242 характеристики,
xerox dc 242 brochure,
xerox dc 242 specifications,
xerox dc242 service manual,
xerox dc242 error code 042-326,